[. . . ] Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. Notice: The sign “Pb” below the symbol for batteries indicates that this battery contains lead. For Israel The marking of products using lasers The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. [. . . ] (  Make a call using voice recognition) Settings in memory Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK], or [DIAL NUMBER], then press the knob. If a contact is selected, press the volume knob to show the phone number. To erase a contact from the preset memory, select [DIAL NUMBER] in step 2 and store a blank number. VOICE Make a call using voice recognition to activate the connected phone. 1 Press and hold 2 Speak the name of the contact you want to call or the voice command to control the phone functions. € This unit also supports the intelligent personal assistant function of iPhone. 1 Press 2 Turn the volume knob to select [RECENT CALL], then press the knob. 5 Turn the volume knob to select [DELETE] or [DELETE ALL], then press the knob. DELETE ALL: All names or phone numbers in [RECENT CALL] in step 2 is deleted. 1 Press and hold 2 Turn the volume knob to select [BLUETOOTH], then press the knob. 01 / 02: Boosts low or high frequencies to produce a well-balanced sound at low volume. SPK-OUT *2 00 to +06 (+03): Adjusts the output level of the subwoofer connected via speaker lead. W LEVEL *1 PRE-OUT *3 *4 –08 to +08 (00): Adjusts the output level of the subwoofer connected to the lineout terminals (REAR/SW) through an external amplifier. ; LOW 55HZ / MID 85HZ / HIGH 120HZ: Audio signals with frequencies lower than 55 Hz/ 85 Hz/ 120 Hz are sent to the subwoofer. W PHASE *1 REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [SUB. ) HPF (For KD-R961BT) OFF: All signals are sent to the front/rear speakers.  ; LOW 100HZ / MID 120HZ / HIGH 150HZ: Audio signals with frequencies lower than 100 Hz/ 120 Hz/ 150 Hz are cut off from the front/rear speakers. €05 — +05 (00): Presets the volume adjustment level of each source (compared to the FM volume level). (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speakers. ON: Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression. [. . . ] Full Bandwidth Power (at less than 1 % THD) Speaker Impedance Preout Level/Load (CD/USB) Maximum Output Power 50 W × 4 or 50 W × 2 + 50 W × 1 (Subwoofer = 4 Ω) 22 W × 4 4 Ω — 8 Ω KD-R961BT: 4 800 mV/10 kΩ load KD-R864BT / KD-R862BT / KD-R861BT: 2 500 mV/10 kΩ load ≤ 600 Ω 14. Indd 23 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 23 20/10/2014 11:09:43 AM INSTALLATION / CONNECTION Warning • The unit can only be used with a 12 V DC power supply, negative ground. € Disconnect the battery’s negative terminal before wiring and mounting. € Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit. [. . . ]